60” FINISH CUT C60K H60T 60T H60H H60H E60B E60B
Start engine and move throttle toward slow position to disengage choke. The mower blades clutch will engage as the engine comes up to speed. The mo
For Model H60H: Set the throttle to slow so the mower blades clutch will disengage. Allow engine to cool down for a short time before moving the thr
Look down, to the sides, and behind before and while backing to avoid backing over something or someone. Care should also be taken while backing so t
G. DRIVE BELT REMOVAL AND TENSION Shut off engine and allow mower blades to stop turning before making any adjustments or repairs. Remove the safet
Front Engine Initial Spring Length 15/16” Running Spring Length 1-1/8” to 1-1/4” Figure 9: Belt Pattern and Spring Adjustment (Model C60K) For Mode
Clutch Engaged Spring Length 2-1/4” to 2-3/8” Clutch Disengaged Spring Length no greater than 2-3/4”1/2” With Clutch Engaged 0” With Clutch Disengage
I. LUBRICATION There are up to ten lubrication points on the wing mower -- one spring-loaded idler pivot, two caster wheel pivots, four wheels (on
WING MOWER SPECIFICATIONS Model ModelH60TC60KENGINE:Engine Make Tecumseh Enduro Kohler Command ProEngine Model OHV130-EXE CV 15SCylinders 1 1Cycles 4
WING MOWER SPECIFICATIONS Model ModelE60BH60HENGINE:Engine MakeBriggs & Stratton HondaEngine ModelIntek GXV390Cylinders11Cycles44CrankshaftVertica
ACREASE WING MOWER PARTS MODEL C60K Item Part # Description C60K1 202135 Hex Head Bolt, 3/8" x 3" Fully Threaded 42 204000 Shoulder Bolt, 1/
ASSEMBLY INSTRUCTIONS READ THE COMPLETE ASSEMBLY INSTRUCTIONS BEFORE STARTING THE ASSEMBLY. You should have: - one mower deck assembly - two caster
MODEL C60K 1 23456789 10 11 12 13 14 15 16 17 18 19 20 1 21 22 23 24 25 26 27 2829 30313433 32 19
ACREASE WING MOWER PARTS MODEL H60T Item Part # Description H60T1 202135 Hex Head Bolt, 3/8" x 3" Fully Threaded 42 204000 Shoulder Bolt, 1/
MODEL H60T 1 2345678910 11 12 13 14 15 16 17 18 19 20 1 21 22 23 24 25 26 27 2829 303134 3332 21
ACREASE WING MOWER PARTS MODEL E60B Item Part # Description E60B1 202135 Hex Head Bolt, 3/8" x 3" Fully Threaded 42 204000 Shoulder Bolt, 1/
MODEL E60B 23 1 2394567810 11 12 16 27 28 17 14 15 22 1 20 18 19 23 24 2521 26813
ACREASE WING MOWER PARTS MODEL H60HItem Part # Description Quantity1 202135 Hex Head Bolt, 3/8" x 3" Fully Threaded 42 204000 Shoulder Bolt,
MODEL H60H 251 23456789 10 11 12 13 14 15 16 1 17 18 19 20 21 22 2324252726 28
PARTS LIST 1 2432578 109 6LAWN & GARDEN HITCH PARTS QuantityItem Part # DescriptionH60T, E60B & H60H C60K1 202135 Hex Head Bolt, 3/8"
ATV TONGUE PARTS PARTS LIST 1 4 23 Item Part # Description Quantity1 216002 Wire Lock Pin .31" X 2.50" 22 216009 Screw Pin Shackle Clevis 13
SAFETY SIGNS AND LOCATIONS 275007 – Warning Decal, Belt Shield 275003 – Danger Decal, Cut Hand & Foot 275002 – Warning Decal, General Serial # &a
Note: Tighten the four wheel assembly pivot bolts so that the wheel assemblies will not flop down when the deck is raised off the ground. Caster Sup
OPTIONAL EQUIPMENT OPTIONAL FLOATATION KIT This optional floatation kit features an extra front and back tire that can be bolted in the center secti
30
5. The telescoping hitch can either be installed to the left or right and should clear the back of the tire by about 2”. 6. If one mower is pulled o
C. INSTALLATION OF ATV TONGUE ASSEMBLY (if the lawn and garden hitching was purchased refer to Section B. Installation of Lawn & Garden Hitching
A. HITCH CONFIGURATIONS (Refer to Figure 6) Shut off the engine and allow the mower blades to come to a complete stop before adjusting the spreader
The hitching system is designed so that the wing mower can be pulled directly behind a tow vehicle without a mower deck or as a left or right wing mow
C. ADJUSTING CUTTING HEIGHT Shut off all engines and allow the mower blades to come to a complete stop on the wing mowers and on the tow vehicle bef
4. Adjust the cutting he e height as the tow th Note: To mow in the lower half of the cutting range, set the front caster axles in the bottom ote
Comments to this Manuals